DARKONE33

I got it working had to unitall it and reistall it

All of suden streamless display stopped working. I will excuted the streamless diplay, sims like it working then just get blank screen, can't use the screen, go in to display setting it not showing up there eighther and ends in few seconds.

[quote who="sdrohan" reply="35" id="3949929"] What I need someone to confirm (because we have never seen an issue with this) is why that's a problem (other than looking odd, perhaps misleading) - that in X case, reporting the refresh rate as higher than it actually may be set to is causing problems. If so, what are those problems and what are the best ways to reproduce them? [/quote] I didn't notice it until it was brought up and I have no issue with it but just looks

Its not really a concern for me. It still works as a seamless screen. To add to Anileania's Post Multiplicity is doubling the secondary screens refresh rate. So if I set is to 60hz it shows as 120 hz and if I set it to 144hz it will show 288hz.

[quote who="Neil Banfield" reply="21" id="3949765"] How fast is your network as low compression needs a very very fast network? [/quote] Not using Low compression - for now its stable at defaults just as long I do not use the sidebar. Current setting Using sidebar no matter what configuration standard or high doesn't matter, always go

[quote who="sdrohan" reply="19" id="3949679"] You are confusing us here a bit, Dark... Define for us: 'continuous configuration and setting changes'. What are you doing and where? Have an active KVM connection open: Yes \ No? Have the KVM sidebar open: Yes \ No? Have the KVM sidebar open, an active KVM connection running, and make 'continuous configuration and setting changes': Yes \ No? [/quote] This issue stemmed after upgrading from V3 to V

[quote who="sdrohan" reply="17" id="3949609"] I suspect you cannot reproduce this (#1) without an active KVM connection, correct? Did you attempt to use WinDBG to create a dump for the crash? Neil: If this proves true, perhaps a queue for 'pending changes' for active KVM connections? Sean Drohan Stardock Product Lifecycle Manager [/quote] Doing more deep diving over the weekend, It seams all ties in with the sidebar.

KVM seams to lockup or lag when using the KVM's side bar. Goes back to normal once you close the side bar.

Here is an update on KVM lag and lockups. I was able to get is work with default setting, after rebooting the primary & the secondary. Doing more testing I was able to Triger the issue on command. 1. Opening and configuring Multiplicity on the primary computer causes the KVM to lag, lock up, or crash. This happens less frequently when configuring occasionally, but continuous configuration and setting changes, as I was doing seams to t

I might be able to work on it this weekend[quote who="sdrohan" reply="14" id="3949358"] This is always a tough ask (as its a bit of work) but to the get the most detailed data for any crash, we would very much like dumps from your PC when it happens. This is what you would do to get them for the crash on the Primary: https://support.stardock.com/space/SHC/1347321935/Man

[quote who="Neil Banfield" reply="12" id="3949332"] I suspect given the symptoms that the Multiplv* process is crashing out on the secondary computer. If you look in Windows event log do you see lots of errors? [/quote] I don’t see any errors pertaining to Multiplicity on the secondary but see couple in the primary. Application error Event ID 1000 & 1002 <img src="https://cdn.stardock.us/forums/73/94/7394800/501b9fd

Its is wired, there is no network issue. I can remote in through other mean and it works fine without any lags.

[quote who="sdrohan" reply="8" id="3949321"] Quoting DARKONE33, reply 7 response rate I suspect you mean 'refresh rate', or how KVM is redrawing the remote. I would encourage you to experiment with the KVM setting for such things Sean Drohan Stardock Product Lifecyc

[quote who="sdrohan" reply="4" id="3949246"] Multiplicity 4 beta 2 KVM slow [/quote] I also added my response on: https://forums.stardock.com/531836/multiplicity-4-beta-2-keeps-going-back

[quote who="sdrohan" reply="5" id="3949241"] We have what we believe is a fix for older CPU installs and the settings issue. If you can recreate the conditions for it to fail for you, I would like to PM you a link to that build for testing. Sean Drohan Stardock Product Lifecycle Manager [/quote] I have tested the fix buy recreating the conditions and was abl

[quote who="sdrohan" reply="5" id="3949241"] Quoting DARKONE33, reply 3 Found a workaround for now. Here is what I did. 1. Uninstall Multiplicity from the computers with the issue 2. Reinstall Version 3.6 and configure the encryption key and password. 3. Install Version 4 Beta 2

Did that sever time trying to fix other issues. Install above V3 and also a clean install, Non of them addresses the issue. Also it gets pixelated sometimes like if there is a bandwidth issue. I know there is no network issue. It works fine connecting via VNC and RDP to the computer.

Another issue since upgrading from Multiplicity V3 to Multiplicity 4 beta 2 the KVM is very unstable. Either it is very slow, locks up and constant disconnects. Out of 4 computer with Multiplicity installed only one computer is set for KVM. It is connect VIA wired network.

Found a workaround for now. Here is what I did. 1. Uninstall Multiplicity from the computers with the issue 2. Reinstall Version 3.6 and configure the encryption key and password. 3. Install Version 4 Beta 2 4. On the working secondary computer configure the keys, password and seamless display settings and backup the configuration. 5. Restore the backup on to the problematic computers. Only one computer still prompts select primary o

Did a clean install and still having issues with the same computers. When it a clean install it will always ask for activation or purchase or try and no encryption key will get saved.

I upgraded from Multiplicity 3 to Multiplicity 4 Beta 2 Pro. I have four computers running Multiplicity; installation on the primary and one secondary went smoothly. However, on the other two installations, the configuration window keeps returning to the "Select Primary or Secondary" screen, and changes won’t save. I’ve uninstalled and reinstalled, but nothing seems to work. Currently, it’s functioning with settings carried over from version 3, but I can’t set up Seaml